Go Back  

DIY Electric Car Forums > Members List

Register Blogs FAQ Members List Social Groups Calendar Search Today's Posts Mark Forums Read

jackbauer is on a distinguished road

jackbauer jackbauer is offline

Senior Member

Visitor Messages

Showing Visitor Messages 1 to 7 of 7
  1. mr23
    01-26-2013 01:33 PM
    mr23
    I read you bought the emw evdisplay unit. Do you happen to know where I can get the stream protocol/definition? I haven't found it on the web. If you don't know, would you be willing to capture a sample for me? I could tell you how, using a BT serial application. I'm sure it is just sending out a stream of characters. Thanks.
    -Chris
  2. green caveman
    12-12-2012 10:54 AM
    green caveman
    Damien,

    Do you have any of the Open Revolt source that Paul modified for you - particularly the hall throttle? He's lost it in a disk crash (along with tach code), so if you have anything, could you please pass it along.

    Thanks,
  3. Baldbruce
    12-09-2012 10:03 PM
    Baldbruce
    Considering a BMW EV conversion. How did you handle the ECU and/or the instrument panel interfaces? Thanks in advance for your time.
  4. Gareth747
    03-16-2012 11:02 AM
    Gareth747
    Hi Damian, i am living in Dublin and about to embark on a conversion of a 1974 BMW 2002. I would love tonpick your brains on the subject. Thanks Gareth
  5. Gary B
    01-18-2012 07:13 PM
    Gary B
    Hello Jack Bauer. - I can't get around this font problem. - What is the problem? - Test msg
  6. jackbauer
    12-27-2010 03:25 PM
    jackbauer
    My real name is Damien but dont tell anyone! My car controller has been running sucessfully for the past 9 months with an unmodified revolt control board. That said it is driving a single 800amp igbt. It all depends on the igbt being used.
  7. badfishracing
    12-26-2010 05:05 PM
    badfishracing
    Jack, if that is your real name
    I've been following along the revolt controller build and like a lot of your enhancements. Right now I've just got a stripped down controller with a microcontroller that can output PWM, and the opticoupler and MOSFET driver from the P&S design. Then I've got a bunch of CM400DU-12Fs to drive. Like you've done with your bike contoller.
    With the better caps buffering the MOSFET driver, are you having good luck driving those IGBTs? I've been following the recent Powerex driver board design, but I don't yet see where it's that much better than the Micrel MIC4511 driver. How many IGBTs would you recommend driving with one driver IC?
    Any thoughts would be appreciated.
    Again, you seem to be making some nice enhancements over the P&S design. Definately want to go down that road, but with my own microprocessor.
    Darin

About Me

  • About jackbauer
    Location
    Ireland
    Occupation
    Engineer
  • Signature
    Now, Cole, when you shift the gear and that little needle on the ammeter goes into the red and reads 1000 Amps, that's bad.
    www.evbmw.com
    www.e39ev.com

Statistics

Total Posts
Visitor Messages
Blog
General Information
  • Last Activity: 04-21-2014 02:05 AM
  • Join Date: 01-12-2008
  • Referrals: 0

Friends

Showing Friends 1 to 4 of 4

All times are GMT -6. The time now is 10:09 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Copyright 2009 Green Web Publishing LLC
Ad Management by RedTyger