[[email protected]]

Hi, I am looking for information's about the MES-DEA TIM 600 inverter tuning. I have the software for the inverter, it is saying i need RS232 connection. But i can't acces the inverter.
Anyone has the experience, that do i need a special interface for testing-tuning the inverter? i have prepared the car, but i need to setup the parameters.
Thanks in advance.

 

[Jack-Lee]

Hi, i had the Manual and Programm for this Inverter
Write me an PM, so i could send it to your email (or is your Name your Email?)

 

[[email protected]]

Hi, I've managed to solve the problem. Now i can see all the parameters and tune the inverter.
Now just need to find a diagnostic software for the ZEBRA battery for further diagnostic.
My email address is : [email protected]

 

[vkfzgtk]

Hi!

I'm dealing with the TIM600 as well. Mine won't start the autotuning because I can't get the traction enable activated.
It had a little crash while shipping and a little capacitor fell off the board. Not that bad, just replaced it.
I'm asking myself: should there be any jumper links present on the upper board? Mine doesn' have any.
Could anyone send me a photo of a working board? Would be very helpful...

email is: [email protected]

 

[59 Austin Healey]

Hi all!

Do any of you have the TIM600 software you'd be willing to share. I'm kinda dead in the water without it.

Thanks!
Mark

 

[Jack-Lee]

Hi, i had Software and Manual for this

 

[59 Austin Healey]

Had? As in you don't have it any more?

 

[Jack-Lee]

Have... "My english is not the yellow from the Egg, but it goes"
Send me your Email-Adress via PM and i send you the Software.

 

[59 Austin Healey]

LOL, sorry! I appreciate it!

 

[59 Austin Healey]

Hi Jack-Lee,

I sent you a PM but haven't sent one before so not sure if I did it right. Please let me know if you didn't get it.

Thanks
Mark

 

[Richirichnl96]

Hello there,

I am already sorry for my bad english but i will give it a try.
I have a full electric caddy with a fault on the inverter(tim600).
I saw that some people have the software for diagnose on the tim600.
Can anyone send me the software?
[email protected]

Greetings from the Netherlands

Richard

 

[59 Austin Healey]

Hi Richard,

I put a copy of the .iso up on my google drive since I can't send it through gmail.

Here's a link anyone can use to download it. I'll keep it up there as long as I can:

MES-DEA.iso

drive.google.com

Hope this helps,
Mark

Hello there,

I am already sorry for my bad english but i will give it a try.
I have a full electric caddy with a fault on the inverter(tim600).
I saw that some people have the software for diagnose on the tim600.
Can anyone send me the software?
[email protected]

Greetings from the Netherlands

Richard

 

[Richirichnl96]

thank you!
I got it, now i have to figure out how it works

 

[59 Austin Healey]

You and me both. I cannot get the serial port to connect.

Good luck,
Mark

thank you!
I got it, now i have to figure out how it works

 

[Richirichnl96]

I have also No connection by serial Port,
My display gives fault code a10(voltage too low) and when i plug the load cable the car says battery disconnected. 0v and temperature -4

 

[Roxster]

Hi, I've managed to solve the problem. Now i can see all the parameters and tune the inverter.
Now just need to find a diagnostic software for the ZEBRA battery for further diagnostic.
My email address is : [email protected]

Hi Richard,

I put a copy of the .iso up on my google drive since I can't send it through gmail.

Here's a link anyone can use to download it. I'll keep it up there as long as I can:

MES-DEA.iso

drive.google.com

Hope this helps,
Mark

Thanks for posting that information. It was very helpful!

 

[Richirichnl96]

Hello there,

still playing with my electric caddy, fixed the battery problem by repairing the BMI,
But I still got the a10 fault in my inverter display And I can not get communication with the inverter… any ideas? Already tried some different cables but no succes so far

 

[59 Austin Healey]

I can't help. I couldn't get the DC/AC converter to talk on serial so I ripped everything out. I haven't had much time to work on this but if I can't get it talking, I'm gonna rip out all the MES-DEA stuff and start from scratch.

Hello there,

still playing with my electric caddy, fixed the battery problem by repairing the BMI,
But I still got the a10 fault in my inverter display And I can not get communication with the inverter… any ideas? Already tried some different cables but no succes so far

 

[59 Austin Healey]

But, do you have pics of your caddy, I really wanna see it work!!

I can't help. I couldn't get the DC/AC converter to talk on serial so I ripped everything out. I haven't had much time to work on this but if I can't get it talking, I'm gonna rip out all the MES-DEA stuff and start from scratch.

 

[Richirichnl96]

You got an e-mail adress for me? I will send you pictures from the caddy